塑料球壓痕硬度儀
多功能塑料球壓痕硬度儀(帶洛氏)
SLQY-96B
多功能塑料球壓痕硬度儀滿足標準:
GB-T3398.1-2008-塑料硬度測定儀第1部分:球壓痕法
GBT 3398.2-2008 塑料 硬度測定 第2部分:洛氏硬度
GBT 23257-2009 埋地鋼質管道聚乙烯防腐層
多功能塑料球壓痕硬度儀概述:
塑料球壓痕硬度儀是在指用直徑為5MM的鋼球,在規定試驗負荷作用下,垂直壓入試樣表面,保持30S后計算球壓痕面積上所承受的平均壓力測試儀。
多功能塑料球壓痕硬度儀特點:
1、 本儀器核心控制部分通過7寸觸摸屏設置參數并控制。
2、 本儀器變形采集利用國內領先的微型位移傳感器技術,最小位移采集精度為:0.001MM,淘汰了利用數字千分表采集位移精度低、易壞及需要更換電池等缺陷
3、 設置好參數后,點開始實驗后自動加載,實驗結束后自動計算結果,同時壓頭自動復位到初始位置進行下次實驗
4、 本儀器帶有微型打印機,可以對試驗結果進行打印。
5、 本儀器具有3種實驗類型:球壓痕實驗、洛氏硬度、耐壓實驗
多功能塑料球壓痕硬度儀技術參數:
1.初負荷:
球壓痕:9.8N
洛氏:98.07N
2.試驗負荷:
球壓痕:49N、132N、358N、612N、961N
洛氏:588.4N、980.7N
3.壓頭直徑:
球壓痕:Ф5mm,Ф10mm
洛氏:Ф3.175mm,Ф6.35mm,Ф12.7mm
4.試樣高度:4mm
5.壓痕深度指示最小分度值:0.001mm
6.計時量程:可以設定
7.計時精度:±1%
8.示值精度:±1%
9.主機變形量:≤0.04mm
多功能塑料球壓痕硬度儀主要配置及附件:
主機一套
主機壓頭 ¢5mm
微型打印機一臺
使用說明書一份:
備注:本儀器標準隨機配件為球壓痕實驗,如需要其它實驗,請另行選配
親英文版介紹
Multifunctional plastic ball indentation hardness tester (with Rockwell)
SLQY-96B
Multifunctional plastic ball indentation hardness tester to meet the standard:
GB-T3398.1-2008- plastic hardness tester first parts: ball indentation method
GBT 3398.2-2008 plastic hardness determination of second parts: the Rockwell hardness
GBT 23257-2009 of polyethylene coating for buried steel pipeline
Multifunctional plastic ball indentation hardness tester overview:
Plastic ball indentation hardness tester is refers to with a diameter of 5MM ball, in the specified test load, the vertical pressure into the surface of the sample, the average pressure tester is calculated to keep 30S received after the ball indentation area..
Multifunctional plastic ball indentation hardness tester features:
1, the instrument is the core control part through a 7 Inch Touch screen set up parameters andcontrol.
2, the deformation of instrument collection by using technology of micro displacement sensor isthe leading domestic, minimum displacement acquisition accuracy: 0.001MM, eliminated usingdigital micrometer acquisition displacement accuracy is low, easily damaged and need to replace the battery and other defects
3, a good set of parameters, start automatic loading experiment, automatic calculation of the results after the end of the experiment, at the same time indenter automatic reset to the initial position for the next experiment
4, the instrument with a micro printer, you can print the test results.
5, this instrument has 3 types of experiments: ball indentation experiment, Rockwell hardness,compressive experiment
Multifunctional plastic ball indentation hardness tester technical parameters:
1 initial load:
Ball indentation: 9.8N
Rockwell: 98.07N
2 test load:
Ball indentation: 49N, 132N, 358N, 612N, 961N
Rockwell: 588.4N, 980.7N
3 head diameter:
Ball indentation: Phi 5mm, Phi 10mm
Rockwell: Phi 3.175mm, Phi 6.35mm, Phi 12.7mm
4 the sample height: 4mm
5 the indentation depth indicating the minimum graduation value: 0.001mm
6: you can set time range
7 timing accuracy: + 1%
The 8 indication accuracy: + 1%
9 host deformation: less than 0.04mm
The main configuration and accessories of multi-functional plastic ball indentation hardness tester:
Host a
The host pressure head of 5mm
Miniature printer
The use of a specification sheet:
Note: the standard random accessories for the ball indentation experiments, such as the need for other experiments, please use separate selection
塑料球壓痕硬度儀SLQY-96A多功能塑料球壓痕硬度儀信息由北京冠測精電儀器設備有限公司為您提供,如您想了解更多關于SLQY-96A多功能塑料球壓痕硬度儀報價、型號、參數等信息,歡迎來電或留言咨詢。
注:對于醫療器械類產品,請先查證核實企業經營資質和醫療器械產品注冊證情況